On Center Home | MyOnCenter Portal | Start an On-Screen Takeoff Trial | Request a Quick Bid Demo | Contact Us | SALES: 1-866-627-6246
   
 
Learn more about Searching
Looking for help for one of ConstructConnect's Other products? Login


Tools
Table of Contents

On-Screen Takeoff - 10.02.01 Creating Typical Areas (Filling out the Typical Areas Grid) - OST

Views: 1172 Last Updated: 12/06/2024 12:51 pm 0 Rating/ Voters
Be sure to rate this article 5 Stars if you find it helpful!

To set up an estimate using Typical Areas, you must select this option when creating a Bid (You cannot use Typical Areas and Typical Groups in the same Bid).

Setting Up Typical Areas

Enabling the Option

  • Open the Bid's Cover Sheet
  • Select Typical Areas in the "Typicals" drop down.

Adding Typical Areas

Note
You must setup your Bid Areas before setting up Typical Areas, see Related Articles for more information.

After you've setup your Bid Areas, return to the Cover Sheet and,

  • Click the Typical Areas button - the Typical Areas dialog displays (notice your Bid Areas are shown on the left)

On-Screen Takeoff Typical Areas dialog box

  • Click New - the add Typical Area dialog box opens

On-Screen Takeoff Typical Areas dialog box pop-up showing new Typical Area name

  • Type in the name of the new Typical Area - be descriptive and be sure to differentiate between different ceiling (deck) heights, for example: 2 Bed Unit A - 8'00" and 2 Bed Unit A - 10'00"
    • Typical Area Names are limited to 50 characters - we recommend short, but descriptive names
  • Click OK to accept the name

Repeat this for each Typical Area that needs to be defined.

Completing the Typical Areas Grid

Next, you tell On-Screen Takeoff how many times each Typical Area occurs in each Bid Area. In the example below, the unit layout is the same (2 Bed Unit A), however the height is different on the 5th floor of each Building. So, this typical unit repeats 10 times on each floor. The 8'00" Typical Area occurs 10 times on floor 1, another 10 times on floor 2, 3, and 4. The 10'00" unit occurs 10 times on floor 5, in each building. This is shown in our screenshot below:

On-Screen Takeoff Typical Areas dialog box filled in

These numbers are based on counts taken from the project plans - the estimator must determine how many of each Typical Area exists in each area and then transfer those totals to the Typical Areas dialog box. When filling in the Typical Areas grid, use the Typical Area grid fill down button and Typical Area grid fill right button buttons to repeat counts down columns and across rows.

  • Click OK to close the Typical Areas dialog

When this step is completed, On-Screen Takeoff calculates a total count of each Typical Unit, a breakdown for each floor, and subsequently, a total for each building. These total counts can be seen in the Areas drop down list on the Image Tab. As you can see, there are a total of 80 of the 8'00" units and 20 of the 10'00" units.

On-Screen Takeoff Image Tab showing the Bid Areas/Typical Areas drop down with typical areas highlighted

Note
Remember, Typical Areas are Height-Specific. Each count of a Typical Area is exactly the same including the Height - if you are taking off one plan that is 8'00 wall height and another that is 10'00 wall height, you need two Typical Areas to accommodate this.

click here to view the previous article Typical Areas - Overview Assigning Takeoff to a Typical Area click here to view the next article



Product documentation (user guides) describes functionality in the latest version of each major release and may not match the functionality in the version you are using. Please check the Product Information and Downloads pages by clicking one of the product buttons above.

Something Wrong with this Article? Let us Know! The information in this site is protected by copyright by ConstructConnect. You may not reproduce, adapt, or publish any content from this site in whole or in part for any purpose, without the express written consent of ConstructConnect, Inc.
Copyright 2024 - All Rights Reserved.