On Center Home | MyOnCenter Portal | Start an On-Screen Takeoff Trial | Request a Quick Bid Demo | Contact Us | SALES: 1-866-627-6246
 
 
Learn more about Searching
Login


Tools
Table of Contents

OST 3.97 - 06.05 Drawing Area Takeoff (Using an Area Condition to Measure Flooring, Carpeting, Roofing, Concrete, Ceilings, etc.)

Reference Number: AA-03647 Views: 786 Created: 11/19/2019 07:41 am Last Updated: 06/12/2020 01:37 pm 0 Rating/ Voters
Be sure to rate this article 5 Stars if you find it helpful!

Area takeoff is anything quantified with a 'square' measurement. Building objects such as carpeting, roofing, flooring, concrete floors, and ceiling tile are examples of construction items taken off as Areas. Square footage, volume (using the Condition's Thickness), and perimeter (lineal footage) can also be calculated. See Related articles for more information on setting up your Area Conditions.

Warning
Before drawing any takeoff, be sure to set and verify the Scale on each page. See Related Articles for more information on setting and verifying scale.

Snap Angle and the Right Angle Indicator

By default, when you draw takeoff using a mouse, On-Screen Takeoff 'snaps' to 15 degree angles. Hold down the <Shift> key to temporarily override the Snap Angle Indicator and/or Snap settings. The "Snap-Angle" functionality will be disabled as long as you hold down the <Shift> key.

To make drawing segments at right angles easier, the program displays the Right Angle Indicator and snaps the corners to 90 degrees by default.

When using the Right-Angle snap to draw a takeoff object, the segments may not be exactly the same length - although the image is a square, one segment may be fractionally larger than another. This can cause calculations to be a little higher if one of the results is Visible Grid or Visible Tiles and/or if the Condition is set to round segments.  See Related articles for more information on Area Conditions and rounding.

You can disable Snap Angle and the Right-Angle Indicator completely in Tools > Options by changing Snap Angle settings and/or disabling the Right Angle Indicator. See Chapter 9 for details information on setting Options and User Preferences.

Auto Magnify

When an Area Condition is selected, hovering over a spot on the drawing automatically magnifies the region in a small pop-up box next to the cursor. This makes placing the cursor on the exact spot easier without having to zoom the page in closely.

The auto-magnifying popup only displays when the page zoom level is less than the magnifier's "Default Auto Zoom Level" as set in Tools > Options.

To disable the auto-magnifying function, click Tools > Options, and set the "Default Auto Zoom Level" to '0'.

Drawing Area Takeoff - Click-n-Drag (Rectangles)

Select an Area Condition from the Condition List, the cursor changes to the takeoff mode indicator

Click the starting point, this is the anchor

Hold down the left mouse button and drag the cursor diagonally away from the anchor point

Release the mouse button when the area object is complete

Note
Single-Click Area Takeoff makes it easy to takeoff multiple rectangular areas that are not exactly the same size (when copying/pasting will not work).

Drawing Area Takeoff - Point by Point (Polygon)

To draw a polygon (something other than a simple rectangle),

Select an Area Condition from the Condition List, the cursor changes to the takeoff mode indicator

Click at the starting point, this is the anchor

Click once at each corner around the desired area to takeoff

Double-click the last point to complete the takeoff (do not double-click at the starting point)

Note
When taking off an area, it is not necessary or even advised to try draw the final segment. Just double-click at the final point and On-Screen Takeoff connects that point with the starting point (this is called 'closing' an area takeoff). If you try to match up the ending and starting points yourself, you may inadvertantly draw an unneeded segment or create an "unclosable area" (explained below).

Auto-Fill to Linears

Let us say you've taken off the perimeter of a region on your plans using a Linear Condition (such as a room's walls). On-Screen Takeoff allows you to quickly 'Auto-Fill' that closed polygon with one or more Area Conditions.

When taking off an area that extends to a closed linear polygon (all linear objects connect) and the Linear Condition used is set to "Connect to" (in Condition Properties/Advanced), a user can select an Area Condition and double-click within that polygon to 'auto-fill' the area. "Snap to Linear" must be checked in the Advanced settings of the Area Condition. For example, draw a square room's walls using a Linear Condition where all four segments connect at the corners (using Continuous mode is the easiest way). Then, grab an Area Condition, double-click within the room defined by the linear objects and the Area will auto-fill to fit the room.

Auto-Fill is a great way of filling in previously drawing Linear takeoff, however, you can save yourself a lot of time using On-Screen Takeoff's Patent Pending Multi-Condition Takeoff function, see Related articles for more information.

Taking off Curved Areas

To takeoff an area with curved segments, follow the contour as closely as possible using short segments. Override the Snap Angle by holding down the <Shift> key while drawing the segments or disable Snap Settings in Tools > Options.

The curved area above was drawn by drawing five short, straight segments (six clicks for the curve).

Adding Vertices to an Area Segment

After you draw an area takeoff object, it may be necessary to add additional vertices (think of a vertex as a joint between two segments of an area takeoff's perimeter) to change the shape or size of the area takeoff. To add a vertex,

Click the Select tool

Click on the area takeoff object

Move the cursor toward the edge of the takeoff - the cursor changes shape indicating that clicking this point adds a vertex

Click once to add the vertex, notice that an additional vertex point appears on takeoff object

Add as many vertices as needed (in example below, to add a 'bump-in', we need to add four vertices to the area takeoff segment).

To move the vertex points, move the mouse pointer over the vertex and the pointer changes to the move cursor - indicating the vertex is ready to be moved

Move the vertices vertically or horizontally to reform the shape of the area takeoff object

Note
Once a vertex is added, to remove it, use the Select Tool to drag it on top of an adjacent vertex.

"Uncloseable" Areas

On-Screen Takeoff generates an unpleasant 'gong' sound when an Unaccepted Action is performed. For example, when the program does not accept a point when you are drawing Area takeoff. When you hear this sound, return to the last accepted point by hitting the <Esc> key and then trying to click the point again (the <Esc > key backs-up the cursor position one point at a time).

The most common reason for being unable to set a final point to close an Area is crossing lines as shown in the screen shot below. In this example, point 4 cannot be set because it would cause the line 3-4 to cross line 1-2. It is very easy to cause this situation when completing the final segment - that is why it is recommended to allow On-Screen Takeoff to draw the final segment automatically by double-clicking the last point.

Manually Setting the Length of Linear Takeoff Drawing Gridded Areas and Aligning to your Plans



Product documentation (user guides) describes functionality in the latest version of each major release and may not match the functionality in the version you are using. Please check the Product Information and Downloads pages by clicking one of the product buttons above.

Something Wrong with this Article? Let us Know! Copyright 2021 - On Center Software, Inc. by ConstructConnect - All Rights Reserved.